In nature goats almost always stand up on their back legs when eating. Even when goats climb into a tree, they stand up when eating. It is their natural eating position, which these feed troughs allow them to do.
Length x Width x Height 2000 x 500 x 900 = R 1 600 2400 x 500 x 900 = R 1 750 3000 x 500 x 900 = R 2 000
Save money with feed that is dry when it rain, and feed that do not dry out in the sun. The roofs can be taken off the feed troughs by removing 8x 10mm bolts.
Length x Width x Height 2000 x 500 x 900 = R 3 600 2400 x 500 x 900 = R 3 950 3000 x 500 x 900 = R 4 300
Goat ground feed troughs are available in 30cm and 50cm wide. The inside measurement of the 30cm wide feed troughs is 22cm wide, and of the 50cm wide is 42cm wide.
Length x Width x Height 2400 x 300 x 300 = R 1 200 3000 x 300 x 300 = R 1 300 4000 x 300 x 300 = R 1 600 6000 x 300 x 300 = R 2 050 2400 x 500 x 300 = R 1 420 3000 x 500 x 300 = R 1 540 4000 x 500 x 300 = R 1 860 6000 x 500 x 300 = R 2 400
Available in widths of 30cm and 50cm. Inside widths are 22cm and 42cm. The openings that the lambs eat through are 14cm wide. The steel frame can open and close like a lid, to make it easy to throw feed in and to clean the feed trough. The steel frame can be taken off from the feed trough by undoing 2x 10mm bolts
Length x Width x Height 1500 x 300 x 300 = R 1 350 2000 x 300 x 300 = R 1 450 2400 x 300 x 300 = R 1 600 3000 x 300 x 300 = R 1 850
1500 x 500 x 300 = R 1 450 2000 x 500 x 300 = R 1 600 2400 x 500 x 300 = R 1 750 3000 x 500 x 300 = R 2 050
The floats that are included, are low pressure 20mm floats. If the farmer want to use a different float, R200 will be deducted from the price and the farmer install the float of his choice. We will build the back plate and float cover, and drill the hole to the measurements of the float that the farmer will use.
Length x Width x Height 2400 x 300 x 300 = R 1 850 3000 x 300 x 300 = R 1 950 4000 x 300 x 300 = R 2 300 6000 x 300 x 300 = R 2 700 2400 x 500 x 300 = R 1 950 3000 x 500 x 300 = R 2 100 4000 x 500 x 300 = R 2 500 6000 x 500 x 300 = R 3 000
Goat lambing pens with strong steel frames built with 25x25 square tube. The farmer has a choice of 3,55mm or 6mm thick steel reinforced mesh - or 25mm horisontal steel pipes that are welded into the steel frames. Panels connect together with 10mm round bars which is included.
Panels without gates Length x Height Reinforce mesh 3,55mm thick steel 1500 x 1200 = R 680 3000 x 1200 = R 900 4500 x 1200 = R 1 200 6000 x 1200 = R 1 350 Reinforce mesh 6mm thick steel 1500 x 1200 = R 760 3000 x 1200 = R 1 000 4500 x 1200 = R 1 380 6000 x 1200 = R 1 560 Horisontal pipes 25mm 1500 x 1200 = R 750 3000 x 1200 = R 1 030 4500 x 1200 = R 1 350 6000 x 1200 = R 1 600
Panels with swing gates Length x Height Reinforce mesh 3,55mm thick steel 1500 x 1200 (1 gate) = R 940 3000 x 1200 (2 gates) = R 1 280 4500 x 1200 (3 gates) = R 1 760 6000 x 1200 (4 gates) = R 2 100 Reinforce mesh 6mm thick steel 1500 x 1200 (1 gate) = R 1 020 3000 x 1200 (2 gates) = R 1 400 4500 x 1200 (3 gates) = R 1 930 6000 x 1200 (4 gates) = R 2 320 Horisontal steel pipes 25mm 1500 x 1200 (1 gate) = R 1 020 3000 x 1200 (2 gates) = R 1 410 4500 x 1200 (3 gates) = R 1 880 6000 x 1200 (4 gates) = R 2 350
Lamb creep feed gates built with 25x25 square tube and verticle pipes. Panels for the creep feed kraal are built with 25x25 square tube steel frames. The farmer has a choice of 3,55mm or 6mm thick steel reinforced mesh - or 25mm horisontal steel pipes that are welded into the steel frames. Panels connect together with 10mm round bars (included).
Lambs creep feed gates Length x Height 1500 x 1200 = R 1 050 2000 x 1200 = R 1 150 3000 x 1200 = R 1 350
Panels for creep feed kraal Length x Height Reinforce mesh 3,55mm thick steel 1500 x 1200 = R 680 2000 x 1200 = R 750 3000 x 1200 = R 900 Reinforce mesh 6mm thick steel 1500 x 1200 = R 760 2000 x 1200 = R 830 3000 x 1200 = R 1 000 Horisontal steel pipes 25mm 1500 x 1200 = R 750 2000 x 1200 = R 840 3000 x 1200 = R 1 030
Save time when working your goats. The work stations have gates on both sides that opens all the way, so that two people can work at the same time on the goats. Neck clamp works very well. Steel frame build with 32x32 square tube and 25x25 square tube gates.
Without scale = R 9 400 With loadcell scale = R 13 500
Goat neck clamps are built with 32x32 square tube, 3mm thick expanded metal and 5mm thick steel for the gear system. The neck clamps work very easy and effective with the handling of goats as well as sheep.
A strong sliding gate used in your chute (drukgang).We weld on both sides 4x square tubes through which a round bar can be used to join the neck clamp to your existing panels of your chute.
Effective tick control, foot rod and scald. The foot dip through which the goats walk is 20cm deep. Farmers let the goats walk through the foot dip every few days, before the goats go to the veld. The foot dip is available in lengths of 2 meters and 3 meters.
Length x Width x Height 2000 x 600 x 1200 = R 4 200 3000 x 600 x 1200 = R 4 950
The foot dip spray race tunnels are built with 38x38 square tube and 2mm thick sheet metal. The foot dip is 20cm deep and on the floor we weld 12mm round bar so that the goats do not slip. The sprayers are on both sides and in the roof. The entire goat is wet, even under the stomach, legs and tail. The sprayers in the roof spray the head and back. We offer two options of pumps to make it easy to spray the goats anywhere. 12 Volt self priming pump that works from any 12 Volt battery. Electric pressure pump with a priming cylinder.
Length x Width x Height 2000 x 600 x 1100 with 6x sprayers R 12 000 2400 x 600 x 1100 with 9x sprayers R 13 000 Optional extra 32mm ball valve = R 350
The goat bale baskets has 8 verticle square tubes and also 8 halfmoon tubes, which is one more of each than cattle bale baskets. Turn the bale basket on it's side and roll in the bale. Turn the bale basket up and cut the bale ropes off and pull it out. Feed wastage is much less than with the traditional bale rings.
Length x Width x Height 1650 x 1500 x 11000 R 3 150
The salt lick stands frames are build with 2mm thick steel. The expanded mesh that the salt lick block stand on, is 3mm thick steel. The legs are 15cm high, with extra 10cm round bar that are hammered into the ground. The extra steel frame prevents the salt block of being pushed off the salt lick stand. We build salt lick stands without or with the extra frame.
Length x Width x Height 430 x 430 x 150 Without extra frame = R 370 With an extra frame = R 450
Place an order
Contact us for more information or if you have any questions. We build the products on order. Deposit of 70% is payable, with which the steel and materials are bought. Balance payment is payable when the order is built and ready to be collected. No VAT payable. If you would like to place an order, send us the following information. We will send you a quotation. We send the invoice when we receive the balance payment. Business name. Person name and surname. Phone number. Postal or physical address. Email address. Your order, as described in price list.
We do not do transport and deliveries. We can assist with transporters, if the buyer can not arrange for transport. Send us a "pin location" or Google maps location", that we will send to transporters for a transport quotation. We will send the contact details of the transporter to the buyer, so that the buyer can make arrangements direct with the transporter. All payments for transport must be made direct to the transporter. See below link for transporters who regularly do transport for our clients. List of transporters and their details. Click here
