Openings that the lambs eat through are 14cm wide. The steel frame on top of the feed trough can open and close, to make it easy to throw feed in the trough and to clean the feed trough. The top frame can be removed from the feed trough by undoing 2x 10mm bolts.
Length x Width x Height 1500 x 300 x 300 = R 1 350 2000 x 300 x 300 = R 1 500 2400 x 300 x 300 = R 1 650 3000 x 300 x 300 = R 1 850
The included floats are low pressure 20mm floats. If the farmer want to use a different float, R200 will be deducted from the price and the farmer install the float of his choice. We will build the back plate and and float cover, and drill the hole to the measurements of the float that the farmer will use.
Length x Width x Height 2400 x 300 x 300 = R 1 850 3000 x 300 x 300 = R 1 950 4000 x 300 x 300 = R 2 300 6000 x 300 x 300 = R 2 700 2400 x 500 x 300 = R 1 950 3000 x 500 x 300 = R 2 100 4000 x 500 x 300 = R 2 500 6000 x 500 x 300 = R 3 000
Strong lambing pens and kraal panels, which are build with 25x25 square tube and steel reinforced mesh with openings of 10cm x 10cm. Panels connect to each other with 10mm round bar.
Panels without gates Length x Height 1500 x 900 = R 800 3000 x 900 = R 1 000 4500 x 900 = R 1 450 6000 x 900 = R 1 600
Panels with swing gates Length x Height 1500 x 900 (1 gate) = R 950 3000 x 900 (2 gates) = R 1 350 4500 x 900 (3 gates) = R 1 850 6000 x 900 (4 gates) = R 2 200
Sheep lamb creep feed gates build with 25x25 square tube and verticle pipes. Panels on the sides of the creep feed kraal are build with 25x25 square tube and steel reinforced mesh with openings of 10cm x 10cm. Panels connect together with 10mm round bars.
Lambs creep feed gates Length x Height 1500 x 1200 = R 950 2000 x 1200 = R 1 050 3000 x 1200 = R 1 250
Panels for creep feed kraals Length x Height 1500 x 1200 = R 800 2000 x 1200 = R 900 3000 x 1200 = R 1 000
Save time when working your sheep. The work stations have gates on both sides, so that two people can work the sheep at the same time. Neck clamp work very well. Steel frame build with 32x32 square tube and 25x25 square tube for the gates.
Without scale = R 9 400 With loadcell scale = R 13 500
Very strong built with 32x32 square tube, 3mm thick expanded metal and 5mm thick steel for the gear system. The neck clamps work very easy and effective with the handling of sheep as well as goats. On the one side we weld 4x square tubes through which a round bar can be used to join the neck clamp to your existing panels of your chute.
A strong sliding gate used in a sheep chute (drukgang). We weld on both sides 4x square tubes through which a round bar can be used to join the neck clamp to your existing panels of your chute.
Length x Width x Height 1050 x 125 x 900 = R 2 050
Effective tick control, foot rod and scald. The foot dip through which the goats walk is 20cm deep. Farmers let the goats walk through the foot dip every few days, before the goats go out to the veld. The foot dip is available in lengths of 2 meters and 3 meters.
Length x Width x Height 2000 x 600 x 1100 = R 4 200 3000 x 600 x 1100 = R 4 950 Optional extra 32mm ball valve = R 350
The spray race tunnels are built with 38x38 square tube and 2mm thick sheet metal. The foot dip is 20cm deep and on the floor we weld 12mm round bar so that the goats do not slip. The sprayers are on both sides and in the roof. The entire goat is wet, even under the stomach, legs and tail. The sprayers in the roof spray the head and back. We offer a choice of two pumps to make it easy to spray sheep anywhere. 12 Volt self priming pump that works from any 12 Volt battery. Electric pressure pump with a priming cylinder.
Length x Width x Height 2000 x 600 x 1100 (6 sprayers) R 12 000 2400 x 600 x 1100 (9 sprayers) R 13 000 Optional extra 32mm ball valve = R 350
The sheep bale baskets has 8 verticle square tubes and also 8 halfmoon tubes. This is one more of each than for cattle. Turn the bale basket on it's side and roll in the bale. Turn the bale basket up and cut the bale ropes off and pull it out. Feed wastage is much less than with the traditional bale rings.
Length x Width x Height 1650 x 1500 x 1100 = R 3 150
The salt lick stands frames are build with 2mm thick steel. The expanded mesh that the salt lick block stand on, is 3mm thick steel. The legs are 15cm high, with extra 10cm round bar that are hammered into the ground. The extra steel frame prevents the salt block of being pushed off the salt lick stand. We build salt lick stands without or with the extra frame.
Length x Width x Height 430 x 430 x 150 Without extra frame = R 320 With an extra frame = R 370
Place an order
Contact us for more information or if you have any questions. We build the products on order. Deposit of 70% is payable, with which the steel and materials are bought. Balance payment is payable when the order is built and ready to be collected. No VAT payable. If you would like to place an order, send us the following information. We will send you a quotation. We send the invoice when we receive the balance payment. Business name. Person name and surname. Phone number. Postal or physical address. Email address. Your order, as described in price list.
We do not do transport and deliveries. We can assist with transporters, if the buyer can not arrange for transport. Send us a "pin location" or Google maps location", that we will send to transporters for a transport quotation. We will send the contact details of the transporter to the buyer, so that the buyer can make arrangements direct with the transporter. All payments for transport must be made direct to the transporter. See below link for transporters who regularly do transport for our clients. List of transporters and their details. Click here
